storebrain51

How to Change a Subaru Spare Key Get a locksmith in touch if you are missing your Subaru key. Locksmiths will usually cut you keys at a lower cost than the dealer. Subaru car keys are usually either intelligent “push-to-start” fob remote keys or simple metal keys. The Fob key needs to be modified. Keyless Entry System The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your vehicle or the lift gate. The remotes utilize keys in your car to connect to your vehicle's computer. Subaru models have a little known feature dubbed PIN Code Access. You can make a custom number sequence to start and unlock your vehicle. Read the owner's manual to learn how to utilize this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza. If your keys stop working, there's a high chance that the battery in the key fob is dead. The first thing to ensure is that it's got new batteries and you can do this with a portable remote tester or an ordinary multimeter in your garage at home. Next, you'll want to remove the key fob from its case and inspect its transmitter circuit board. You'll be able to see one or two 8-digit sets. Note down the first one so you can remember it. After you've completed this, you can begin programming your key fob at home. This process varies according to the year and model of your car. However, it is usually easy enough to do yourself. Key Fobs Subaru's latest models have key fobs that not only unlock doors but also switch on lights, lock gas cap and even start the car. That last trick is especially helpful if you've been at the gas station only to discover that your car isn't starting because the battery for the key fob died. Whether your Subaru is new or old, it's likely that the key fob can be replaced with no difficulty. It's important to note that models with the highest level of technological sophistication may require a trip to the dealership. With a little effort and time, you can make your own replacement key fob. Start by examining the transmitter circuit board inside your key fob (instructions to open the case should be provided in your owner's handbook). It should have one or two sets of serial numbers, each of which is 8 digits long. Note down the first number in the series and keep it in a safe place to refer to later on. After that, get in your driver's seat, and close all the doors. Turn the key to start the vehicle and then switch off after 10 turns. Press the lock button on your key fob and open the door to check that all of your doors function properly. Close the door, and then take the key off. You should hear your car beep again, indicating that the key fob is programmed. Ignition System If your Subaru keys aren't working as they should it could be due to the fact that the battery is dead. You can replace the battery for your key fob by yourself if are familiar with the procedure. subaru legacy key replacement is cheap and simple to locate. If the key fob isn't responding to your commands it could be an issue with a different cause. It's recommended to go to a dealer to obtain an extra key. They'll ensure that the key is an original Subaru key, which is covered under warranty, and that it will be programmed for your vehicle. This is much simpler and safer than buying an aftermarket one from a company online. You can also ask the dealer cut a new key if you supply them with your VIN number and proof of ownership. The information provided will be used to code the replacement key so that it is recognized by your immobilizer. This is a more complicated procedure than cutting a key, and the dealer will charge more for it. Once the new key has been programmed, you are able to switch it over to the working key. It will take only five seconds to insert the second key, so it's essential to keep an active key in your bag. You can take the key off when the security light has stopped flashing and you can test it. Battery Replacement Subaru fobs are extremely useful because they can switch on the power windows and sunroof of your vehicle with a single button press. The battery inside your Subaru fob isn't designed to last forever, and will need to be replaced at some point. It's good news that replacing the battery is a straightforward procedure that you can do yourself with the assistance of this brief guide from Capitol Subaru. You'll first need to find the small crevice that is the gap between the front and back of your keyfob. You can cut this gap using the flat-head screwdriver, which will reveal the small compartment that contains the battery. Remove the battery that was in it, and then install a new one, making sure it is facing the right side up. After everything is in place and you are able to use your new key fob to lock, unlock, and start your vehicle easily! It's always best to have an extra set of keys available particularly if you've lost them or they're not working properly. You can purchase a replacement key at your local dealership or get it cut by locksmiths. It is important to ensure that your key fob functions well as soon as possible so that you can safely drive.